FIRMWARE RELEASE NOTES
                        ======================

Products affected: AXIS P5512 PTZ Dome Network Camera

Release date:      2012-03-08

Release type:      Production

Firmware version:  5.25.1

File name:         P5512_5_25_1.bin

Preceding release: 5.25

AMC version:       5.9.9.0-1


------------------------------------------------------------------------------

UPGRADE INSTRUCTIONS
====================

The firmware can be upgraded using Axis Camera Management, HTTP or FTP.
Please follow the instructions from the user's manual, the web page at
http://www.axis.com/techsup/cam_servers/how_to_upgrade.htm or the file named 
howtoupgrade.txt.


RELEASE 5.25.1
==============

5.25.1 is a production service release for AXIS P5512.

Corrections in 5.25.1 since 5.25
================================

5.25.1:C01  Corrected the SSP/PPS H264 parameters time stamps,
            now it will be the same as the following I-frame.

5.25.1:C02  Socket leak during Guard Tour which caused
            the camera to slow down.

5.25.1:C03  Ethernet driver and streaming fixes added,
            should correct some cases where the camera was left unresponsive.

5.25.1:C04  Slow shutter exposure time is restored after reboot.


Known Bugs/Limitations
======================

5.25.1:L01  Audio clip upload size limit, limited to less than ~1.5MB.

5.25.1:L02  Motion detection reacts to IR cut filter switching.

5.25.1:L03  Uploading an expired or not yet valid encrypted client certificate in PKCS#12 format for 802.1x will succeed instead of being rejected as it should be

5.25.1:L04  RTSP clients timeout when syncing unit to computer time due to the keepalive messages being regarded as too old/new depending on the time set.

5.25.1:L05  Cannot record audio clip with no wait time. You must wait at least 1 second.

5.25.1:L06  Errors in log when removing micro SD card without unmounting it first.

5.25.1:L07  Focus can sometimes be poor on the ELMO 401C block.

5.25.1:L08  Criticals found in system log at restart when Guard tour is running.

5.25.1:L09  Control panel is hidden behind the video sometimes. The AMC component is uncontrollable by the web viewer.

5.25.1:L10  After a factory default,the default PTZ home position not defined when the PTZ framework is told to go to the home position; the the camera will remain at the calibration point.

5.25.1:L11  Onvif failing test case 6.2.24. This is due to a bug in the test tool and test specification, i.e. the Axis interpretation is correct.

5.25.1:L12  No warning message in log when pre-trigger buffer is too large.

5.25.1:L13  ONVIF speed param is ignored by the camera.

5.25.1:L14  MJPG recordings to SD card with too high bitrate may cause oom kill of monolith. Lower the bitrate to a rate that the SD card/controller can handle. Can not give specifics since it differs between SD cards.

5.25.1:L15  From time and duration not respected in continuous recording <5 min; Cue points not available and seeking is not possible until a MKV-file is finalized (stopped or full 5 minutes).


Application Developer Information
=================================

The AXIS VAPIX Application Programming Interface version 3 is supported by 
the AXIS P5512.

Supported AXIS VAPIX API Image Resolutions for AXIS P5512

Resolution  Exceptions
==========  ==========
4CIF
704x576     1)
704x480     2)
2CIF
704x288     1)
704x240     2)
CIF
352x288     1)
352x240     2)
QCIF
176x144     1)
176x120     2)

1) Only available for 50Hz cameras
2) Only available for 60Hz cameras

90/270 degress rotation is not supported.