FIRMWARE RELEASE NOTES ====================== Products affected: AXIS P1344/P1344-E Network Camera Release date: 2012-04-25 Release type: Production Firmware version: 5.40.9.1 File name: P1344_5_40_9_1.bin Preceding release: 5.40.9 AMC version: 6.0.6.7-1 ------------------------------------------------------------------------------ UPGRADE INSTRUCTIONS ==================== The firmware can be upgraded using Axis Camera Management, HTTP or FTP. Please follow the instructions from the user's manual, the web page at http://www.axis.com/techsup/cam_servers/how_to_upgrade.htm or the file named howtoupgrade.txt. Corrections in 5.40.9.1 since 5.40.9 ==================================== 5.40.9.1:C01 Several improvements for stability. 5.40.9.1:C02 Handling of sockets when running the ONVIF operation GetNetworkInterfaces has been improved. 5.40.9.1:C03 Web service deamon memory handling improved. 5.40.9.1:C04 Trigger data (SEI NAL) works as expected. 5.40.9.1:C05 Sending DHCP release has been adjusted for environments with DHCP snooping. 5.40.9.1:C06 HTTP upload event with authentication works as expected. 5.40.9.1:C07 The error condition encountered when creating two similar action rules (or by a copied action rule) has been fixed. 5.40.9.1:C08 The problem of I/O port being stuck in active mode after a while of event triggering has been fixed. 5.40.9.1:C09 The trigger type for tampering is reported with the correct value (T0:/ instead of T1:/). 5.40.9.1:C10 An adjustment for intermittently twitching stream during higher load has been made. Known Bugs/Limitations ====================== 5.40.9.1:L01 It is recommended to unmount the SD Card before ejecting it. 5.40.9.1:L02 Recordings made with firmware earlier than 5.20 will not be readable on the SD Card from the 5.40 firmware. Backup important recordings and reformat the SD Card after the firmware upgrade. 5.40.9.1:L03 Remote back focus operation will be disabled when temperature is too low. Information will be shown in the system log. 5.40.9.1:L04 Check and repair is only available if the file system is ext4. 5.40.9.1:L05 Recording streams with a total bit rate above 12Mbit/sec to SD Card may cause missing frames/sequences. 5.40.9.1:L06 When using action rule resulting in short recordings, it is recommended to extend post-event time. 5.40.9.1:L07 With audio enabled, the initial connection latency increases. 5.40.9.1:L08 Sometimes IR cut filter switches between ON/OFF after factory default when illuminance is 7-10 lux. 5.40.9.1:L09 Color parameter has no effect when pulling RTSP stream with color=0. Application Developer Information ================================= The AXIS VAPIX Application Programming Interface version 3 is supported by the AXIS P1344/P1344-E. For more information, please refer to the AXIS VAPIX HTTP API specification version 3, part of the AXIS VAPIX API, available at www.axis.com. Supported AXIS VAPIX API Image Resolutions for AXIS P1344/P1344-E Resolution Exceptions ========== ========== 1280x800 1280x720 1024x768 1024x640 800x600 800x500 800x450 640x480 640x400 640x360 480x360 480x300 480x270 320x240 320x200 320x180 240x180 176x144 160x120 160x100 160x90 1440x900 1) 768x576 1) 720x576 1) 704x576 1) 704x480 1) 704x288 1) 704x240 1) 384x288 1) 352x288 1) 352x240 1) 240x135 1) 192x144 1) 176x120 1) 80x50 1) 1) Not visible in web user interface