FIRMWARE RELEASE NOTES ====================== Products affected: AXIS P7224 Network Camera Release date: 2011-12-22 Release type: Production Firmware version: 5.40.7 File name: P7224_5_40.bin Preceding release: n/a AMC version: 6.0.6.4-1 ------------------------------------------------------------------------------ UPGRADE INSTRUCTIONS ==================== The firmware can be upgraded using Axis Camera Management 2.0, HTTP or FTP. Please follow the instructions from the user's manual, the web page at http://www.axis.com/techsup/cam_servers/how_to_upgrade.htm or the file named howtoupgrade.txt. RELEASE 5.40.7 ============ 5.40.7 is the first official production release for the AXIS P7224 Known Bug/Limitations ===================== 5.40.7:L1 Missing recording functionality over network share for products with no SD-card support. 5.40.7:L2 802.1x does not work in a Q7900 rack if a blade is placed in any of the rack positions 1, 5, 8, 11 5.40.7:L3 The 'Any' event does not work when triggered with the virtualinput.cgi 5.40.7:L4 It's not possible to get an event due to power-supply failure in a Q7900 rack 5.40.7:L5 Parameter PTZ.CamPorts.Cam#Port shall be -1 when no PTZ driver is installed, However on multi channel products the value is always > 0 for all but the first channel. 5.40.7:L6 ptz.cgi returns unexpected values when no driver is installed on multi channel products 5.40.7:L7 AVHS radio button not enabled after enable and save 5.40.7:L8 In an AVHS installation, the clock is not synchronized with the AVHS server which may lead to incorrectly scheduled recordings. 5.40.7:L9 ONVIF discovery source address is not correct. The link local address is used as a source address, this is not according to RFC 3927 (section 2.7): 5.40.7:L10 When using the H.264 rate controller with a low GOV length (e.g. 3) you can get disrupted video. Use GOV length > 10. 5.40.7:L11 Network lost trigger is not available in Action rule setup. 5.40.7:L12 TCP notify in an Action rule doesn't work as expected. 5.40.7:L13 When action rules run, the name of the rule will sometimes be incorrectly logged in the system log. 5.40.7:L14 The center mode for click-in-picture doesn't work for ptz-control when using loadable drivers. 5.40.7:L15 The sound level is very high when there is no audio source connected. If the high-pass filter in the audio codec is enabled the level will be low. 5.40.7:L16 Invalid multicast address in SDP content. 5.40.7:L17 90 and 270 rotation can cause a drop in frame rate. ================================= The AXIS VAPIX Application Programming Interface is supported by the AXIS P7224. The following groups are supported by this product. For more information, please refer to the AXIS VAPIX HTTP API specification version 3, part of the AXIS VAPIX API, available at www.axis.com. Group Exceptions ===== ========== General Image and Video PTZ Set PTZ parameters (ptzparam.cgi) Motion Detection I/O Serial port IP filter Audio Built in templates for dynamic parameters are: Template Group ======== ===== 'audioclipaction' Event.E#.Actions 'button' PTZ.Auxiliary.A1.Button 'event' Event 'ftp_config' EventServers.FTP 'ftpaction' Event.E#.Actions 'guardtour' GuardTour 'guardtouraction' Event.E#.Actions 'http_config' EventServers.HTTP 'httpaction' Event.E#.Actions 'hwaction' Event.E#.Actions 'mediaclip' MediaClip 'motion' Motion 'ptzaction' Event.E#.Actions 'ptzsensoraction' Event.E#.Actions 'smtpaction' Event.E#.Actions 'streamcache' StreamCache 'streamprofile' StreamProfile 'tcp_config' Eventservers.TCP 'tcpaction' Event.E#.Actions 'tour' GuardTour.G#.Tour 'user_ctlqueue' PTZ.UserCtlQueue Supported AXIS VAPIX API Image Resolutions for AXIS P7224. Resolution Exceptions ========== ========== 16CIF 1536x1152 1) 3) 1280x960 2) 3) XGA 1024x768 3) D1 720x576 1) 720x480 2) 4CIF 704x576 1) 704x480 2) 2CIF 704x288 1) 704x240 2) CIF 352x288 1) 352x240 2) QCIF 176x144 1) 176x120 2) 1) Only available for PAL cameras 2) Only available for NTSC cameras 3) Only available for Quad channel