FIRMWARE RELEASE NOTES
                        ======================

Products affected: AXIS P5522 PTZ Dome Network Camera

Release date:      2012-03-21

Release type:      Production

Firmware version:  5.25.1

File name:         P5522_5_25_1.bin

Preceding release: 5.25

AMC version:       5.9.9.0-1


------------------------------------------------------------------------------

UPGRADE INSTRUCTIONS
====================

The firmware can be upgraded using Axis Camera Management, HTTP or FTP.
Please follow the instructions from the user's manual, the web page at
http://www.axis.com/techsup/cam_servers/how_to_upgrade.htm or the file named 
howtoupgrade.txt.


RELEASE 5.25.1
==============

5.25.1 is a production service release for AXIS P5522.


Corrected problems
==================

5.25.1:C01  Corrected the SSP/PPS H264 parameters time stamps,
            now it will be the same as the following I-frame.

5.25.1:C02  Socket leak during Guard Tour which caused
            the camera to slow down.

5.25.1:C03  Ethernet driver and streaming fixes added,
            should correct some cases where the camera was left unresponsive.

5.25.1:C04  LLDP broadcasts the proper MAC address.

5.25.1:C05  Improved SHTTP client.

5.25.1:C06  Center command with specified image height works properly.


Known limitations
=================
5.25.1:L01  Audio clip upload size limit, limited to less than ~1.5MB.

5.25.1:L02  Motion detection reacts to IR cut filter.

5.25.1:L03  PKCS#12 with encrypted certificates are not time verified.

5.25.1:L04  SNMP test 5.4.0.1 fails over IPv6.

5.25.1:L05  SNMPv3 SilverCreek 4.20.8 (IPv6).

5.25.1:L06  RTSP clients timeout when syncing unit to computer time.

5.25.1:L07  Cannot record audio clip with no wait time.

5.25.1:L08  Error when removing micro SD card without unmounting it first.

5.25.1:L09  Criticals found in system log at restart when Guard tour is running.

5.25.1:L10  Control panel hidden behind the video sometimes.

5.25.1:L11  After a factory default,the default PTZ home position not defined when the PTZ framework is told to go to the home position; the the camera will remain at the calibration point.

5.25.1:L12  6.2.24 - Onvif failing test case: "This is due to a bug in the test tool and test specification, i.e. the Axis interpretation is correct.

5.25.1:L13  No warning message in log when pre-trigger buffer is too large.

5.25.1:L14  ONVIF speed param is ignored by the camera.

5.25.1:L15  MJPG recordings to SD card with too high bitrate may cause oom kill of monolith.

5.25.1:L16  Relative tilt applied despite tilt control being disabled when Auto-flipping.

5.25.1:L17  From time and duration not respected in continuous recording <5 min; Cue points not available until a MKV-file is finalized.

5.25.1:L18  Guard Tour View time is longer than stated in setup due to Focus/Iris taking some extra time.



Application Developer Information
=================================

The AXIS VAPIX Application Programming Interface version 3 is supported by 
the AXIS P5522.

Supported AXIS VAPIX API Image Resolutions for AXIS P5522

Resolution  Exceptions
==========  ==========
D1
720x576     1)
720x480     2)
4CIF
704x576     1)
704x480     2)
2CIF
704x288     1)
704x240     2)
CIF
352x288     1)
352x240     2)
QCIF
176x144     1)
176x120     2)

1) Only available for 50Hz cameras
2) Only available for 60Hz cameras

90/270 degress rotation is not supported.