BODY WORN SYSTEM FIRMWARE RELEASE NOTE ====================================== Products affected: W100, W800 Release date: 2020-10-27 Release type: Production Firmware version: 10.1.0.1 Preceding release: 10.0.3.1 Languages: English, German, French, Spanish, Italian Compatibility: AXIS IP Utility 4.14 or above, AXIS Camera Station 5.33 or above, AXIS Body Worn Assistant, Genetec Security Center 5.9.2.0 or above, Milestone XProtect 2020 R1 + AXIS Optimizer Body Worn Extension 1.0.55 or above, Genetec Clearance, Google Chrome ------------------------------------------------------------------------------------------------------------------------- New features in 10.1.0.1 since 10.0.3.1 ======================================= * Support for mobile app AXIS Body Worn Assistant. * System configuration information is included in BWS system report. Corrections in 10.1.0.1 since 10.0.3.1 ======================================= * Further improvements in time sync between BWCs registered in the same system, allowing for synchronised playback on recordings from different BWCs. New features in 10.0.3.1 since 9.75.1.1 ==================================== * W800 with access to axis.com will get notification when a new firmware is available. * Improved time sync between BWCs registered in the same system, allowing for synchronised playback on recordings from different BWCs. Corrections in 10.0.3.1 since 9.75.1.1 ==================================== * "System reset" is now under "Support" menu to make it more visible in Body Worn Manager (BWM). * In previous versions, the BWC did not always notify the end user in case of a malfunctioning recording capability. Now it gives an operation error, operation status led in amber, if this occurs. * During system setup wizard, when there is no NTP server in place and the user does not uncheck "NTP server" on the "Date and time" page, there is no error notification until the user arrives at the Summary page (The "Next" button is disabled and system setup can not be finished). Now it is required to set "Manual time" on the "Date and time" page in order to proceed. * If a BWC (or user) is removed from Body Worn Manager when there are recordings left on the BWC (assigned to the user), the recordings may not be transferred to the content destination. * Sometimes firmware upgrade fails during setup wizard and no immediate error message is given. * When using HTTPS to connect to Body Worn Manager and leaving the browser open on "Devices", Body Worn Manager will stop responding after a few days, although it is still possible to dock and undock BWCs as normal. The problem is gone after a reboot of the system controller. Corrections in 9.75.1.1 since 9.75.1 ==================================== * Corrected Axis critical vulnerability ACV-2020-100004. For more information please visit www.axis.com/support/product-security. Known Bugs/Limitations ====================== * Can't remove a camera if connection to content destination is broken. * An unregistered BWC with older firmware shows up underneath "New" section in Body Worn Manager and then disappears during firmware upgrade until after the firmware is upgraded. If the end user "Add" the BWC before the firmware is upgraded, it needs to be done again after that. * Connection status on the content destination page under "Settings" is not refreshed automatically after a new connection file is uploaded. A page refresh solves the problem. * The list of BWCs in BWM are not always complete after firmware is upgraded in BWM. Sometimes only the BWCs that have not been upgraded are listed. A refresh on the page will solve the problem. * Recordings may not be transferred to the content destination if there is not enough licenses on the content destination. * If a BWC has not finished offloading recording on one system controller, it can't be used on another system controller in the same system until the offloading is finished. * When a BWC is undocked immediately after it is removed, the BWC can get stuck in the "unregistering in process" state in Body Worn Manager. The problem is gone when docking the BWC again and waiting for it to show underneath "New" section in Body Worn Manager. * If a BWC's license is deactivated in Genetec Clearance, it's not possible to remove it from BWM. Reactivating the license in Clearace will solve the issue. * When using Security Center as the content destination, if the time difference between system controller and Security Center is bigger than 15 seconds, a default user named by the camera's mac address is created. All recordings created with that BWC will be uploaded to the default user. * Putting BWC back to back against a radio device can cause black screen and a flickering image, which can take a while to recover. The same thing won't happen if they are placed side by side.